Wednesday, September 30, 2015

Sewing on marabou feather trim - a mini tutorial

A few people have asked me about sewing on marabou feather boa trim...so I decided to do a quick little tutorial explaining how to work with this stuff, and hope that it is helpful!

I used marabou feather boa trim on the following projects: 18th century pink silk w/ white marabou hooded cape, 18th century black silk w/ black marabou hooded cape, my fluffy white modern hat, and most recently, my early 19th century (Regency) cream silk w/ white marabou pelerine.

18th C pink silk hooded cape 
19th C cream silk pelerine
Resources: All of the marabou feather boas I bought at my local JoAnn's or ordered from JoAnn's.com. Link to boas here (also I used sale coupons).

Also on the sidebar (near top) is a link to my Pinterest board of capes, cloaks, pelerines, mantles, and other examples of historical outerwear, many of which have marabou trim OR ermine or other furs.

There are different methods for sewing on marabou trim, and what I used was intended to very thoroughly secure the marabou to the cape/pelerine edges, and minimize the amount of feather shafts (the hard middle part of the feather) that stick up. I did this by securing the marabou every 1/8-1/4 inch instead of every 1/2 or 1 inch or so, which was laboriously and difficult, but ends with a lovely finished product!

Finding the SMOOTH side: Pick up the marabou feather boa and stroke it a few times in opposite directions, finding the smooth side (the side that strokes the feathers down versus standing up). The smooth side direction top will be your top edge. This is what you want to start with, to secure on your cape/cloak/etc. Keep in mind that you want the feathers to smooth DOWN, so if you are starting with the hood, find the middle of the hood at the top, and then start there and make sure the feather boa is smooth going down one side of the hood, then using a separate piece, start again on the other side of the middle ensuring that the feather boa is smooth going down the second side of the hood.

Marabou feather boa, SMOOTH side versus NON SMOOTH side:

SMOOTH side
NON SMOOTH side
The same holds true for the cape or pelerine edges, you want the marabou to lay smooth going down, so ensure that you start at the top and sew down the cape/cloak/peleriene edge, with the marabou smooth side going down (going down the vertical). Areas of the cape/cloak/pelerine that are horizontal can be smooth going either way, so I just continue the smooth direction already in process and keep going.

Sewing it down: Using a needle that has been double-threaded (I used Mettler's 100% cotton), First, you gently cut away the bit of rope at the end of the feather boa, leaving you with only feather shafts (use non-sewing scissors). Starting from the bottom (lining side) hide a thread knot underneath the edge of the bias binding, coming up slightly over the middle on the top edge (above the marabou).

Start your needle from below, hide knot
(View without flash)
Take your needle OVER the marabou (hard to see)
Then take your needle across the marabou below to enter your needle in just on the other side of the marabou trim (so as to cover the feather boa with your double thread and secure it) and come out the bottom side. Again, starting from the bottom, come up slightly over the middle of the top edge (above the marabou), then take your needle across the marabou, covering it with your double thread and through below to come out the bottom side. Repeat a few times in the same area to well secure the cut top end of the marabou boa. Then move on by repeating the above steps to sew down the marabou trim by securing it every 1/8-1/4 inch.

Continue with the above, sewing down all the marabou feather trim using double thread thickness (for securing) and hiding your knots as you go. It's fine if your stitches overlap each other a bit, it will make the marabou edge very secure.

Finishing: Once you have completely sewn on all the marabou trim (keeping in mind it should be SMOOTH vertically), you will now need to 're-fluff' the marabou! The double thread is now holding down (trapping) the fluffy marabou feather bits along the edge, and you will get a beautiful finished edge when you re-fluff it. Taking a needle or pin, hold the marabou up vertically (smooth or rough side doesn't matter).
Gently work out the fluffy feathers to release them from the (now) horizontal threads, picking out a small bit at a time, making sure not to pull too hard. If you pull too hard, the thin shafts of the feather fluff will break, so work gently and carefully.
Fluffing the marabou
See how the marabou is 'trapped' under the thread?

Fluffy marabou again!
Free as much of the marabou feather fluff as you can, and voila! You are DONE!!

Tips and tricks: The marabou feather fluffy bits MAY get caught up in your thread at times. If so, stop pulling and gently work at the area with your needle until your thread is able to be pulled through again. For me, it seemed to happen more with the white marabou boas then the black ones: the white ones were not quite as 'full' as the black ones, so this quality difference seemed to affect how easy it was to sew down without getting caught.

Note: if you are not looking to secure the marabou well and want to re-use it on other projects, you can sew down the marabou trim every 1/2 to 1 inch or more, and it may move around a bit but can be possibly removed later for re-use. I wanted my garments to last so choose the above securing method.

And there you go, I hope this mini tutorial was helpful!

4 comments:

  1. Brilliant - just what i was looking for. thank you

    ReplyDelete
    Replies
    1. You are SO welcome, glad it helped! So sorry I didn't see this comment before now, I'm relatively new to blogging, but I hope your sewing turned out well and you enjoyed the process or at least the finished result (isn't wearing something with marabou SO fun, I feel like a fluffy princess when I do, LOL), maybe even share a pic? :) Happy Holidays!!

      Delete
  2. Hello, do you have any tips for sewing a marabou trim onto a leotard? I am not a natural seamstress but have to make a costume for an aerial show I am performing in. I have avoided sewing through the elasticated part of the leotard but am finding that even so the stretchiness is very reduced and it is quite difficult to put on! Thank you, Rose

    ReplyDelete
    Replies
    1. Hi there, so sorry I missed this comment! I've not sewn marabout onto a leotard yet, but yes, you're correct, when you sew thru an elastic part or add a lot of stitching or trim that tends to stiffen and hold things in place which would make it less stretchy and harder to put on. You are right on there! I would say to tack it on every couple of inches may help to reduce the stitches in the elastic or leotard. I hope your aerial show went or is going well, that sounds so great!

      Delete